IB MYP · Sciences — Physics
Gr_10_D,E,F_EOT-1_Physics_QP_2025-26
End of Term 1 Examination · 33 questions · 100 points · Duration: 2 hours
Instructions to candidates
• Answer all questions in the answer boxes provided. Type your working using the MathType (√x) button for formulas.
• Unless otherwise stated, take the acceleration due to gravity as g = 9.81 m s⁻² and give answers to an appropriate number of significant figures.
• A calculator is required. Videos and PhET simulations referred to in this paper are watched/run in the original exam — this copy keeps the same questions.
• The maximum mark for each question is shown in brackets, e.g. [A 4] (A = Knowing & Understanding, B = Investigating, C = Communicating, D = Thinking Critically).
• Answer all questions in the answer boxes provided. Type your working using the MathType (√x) button for formulas.
• Unless otherwise stated, take the acceleration due to gravity as g = 9.81 m s⁻² and give answers to an appropriate number of significant figures.
• A calculator is required. Videos and PhET simulations referred to in this paper are watched/run in the original exam — this copy keeps the same questions.
• The maximum mark for each question is shown in brackets, e.g. [A 4] (A = Knowing & Understanding, B = Investigating, C = Communicating, D = Thinking Critically).
SECTION 1 — Periodic motion
Q 1.1[A 1]
Look at the images below and decide if the motion is periodic or non-periodic.
Image 1 — (see original exam — optionally paste the picture here)
Image 2 — (see original exam — optionally paste the picture here)
Image 3 — (see original exam — optionally paste the picture here)
▶
Video — Pendulum in motion
Watch this video in the original exam (AssessPrep), then answer questions 1.2 – 1.4.Q 1.2[A 1]
Define periodic motion.
Q 1.3[A 2]
Consider a pendulum swinging back and forth. Let Position B be the lowest point of its swing, and Positions A and C be the highest points on either side.
Identify the statement that correctly describes the energy at Position B.
Identify the statement that correctly describes the energy at Position B.
Q 1.4[A 4]
A pendulum can be used to demonstrate periodic motion. The period T of a pendulum is the time taken to complete one swing. T depends on the length of the pendulum, L, and the acceleration due to gravity, g, given by the relationship
A student sets up an experiment in a laboratory in Canada, where g is known to be 9.79 m s⁻². They use a pendulum of length L = 72.5 cm.
Calculate the time it would take for this pendulum to complete 10 full swings. Give your answer to three significant figures.
T² = 4π²L / g
A student sets up an experiment in a laboratory in Canada, where g is known to be 9.79 m s⁻². They use a pendulum of length L = 72.5 cm.
Calculate the time it would take for this pendulum to complete 10 full swings. Give your answer to three significant figures.
Q 1.4 (b)[C 2]
The accepted value for g in the laboratory is 9.82 m s⁻². Using the data from the experiment (L = 0.725 m and T = 1.71 s), the student calculates an experimental value of g ≈ 9.79 m s⁻², which is lower than the accepted value.
Propose one plausible source of systematic error that would cause the calculated value of g to be artificially low. Justify your answer by explaining the error's effect on the measured variables L or T.
Propose one plausible source of systematic error that would cause the calculated value of g to be artificially low. Justify your answer by explaining the error's effect on the measured variables L or T.
Q 1.5[A 4]
The diagram shows a wrecking ball hanging from a crane, initially stationary at a height of 12.5 m above the ground. The crane operator releases the ball and it swings down towards a building, hitting it at a height of 4.5 m above the ground (points A and B on the diagram).
Diagram — wrecking ball (see original exam; optionally paste it here)
Calculate the kinetic energy of the ball when it hits the building at 4.5 m above the ground. Assume g = 9.81 m s⁻². Give your result in kJ, rounded to two significant figures.Q 1.6[B 2]
Suggest why the real-world kinetic energy of the wrecking ball would be lower than the calculated value.
SECTION 2 — Investigation: water clocks
▶
Video — “Water Clocks” (39 s)
Watch this video in the original exam (AssessPrep), then answer questions 2.1 – 2.6.Q 2.1[B 3]
Below is a list of variables for this experiment. Select the appropriate description for each of the variables and fill in the table.
| Variable | Description |
|---|---|
| Type of liquid | |
| Area of the out-flow tube | |
| Time it takes for the water to drain out |
Q 2.2[A 1]
State the question that could be answered in this scientific investigation.
Q 2.3[B 2]
Formulate and explain the hypothesis that this investigation would test.
Q 2.4[B 3]
Identify two pieces of measuring equipment you would need to perform this experiment.
Q 2.5[C 1]
Describe the data you will collect.
Q 2.6[B 3]
The cylinder is then drilled with a hole at a height of 20 cm. Water fills to 50 cm then drains out through the hole.
Predict the time taken for the water to drain through the hole. Show your working. Assume g = 9.81 m s⁻². Round your result to 2 significant figures.
Predict the time taken for the water to drain through the hole. Show your working. Assume g = 9.81 m s⁻². Round your result to 2 significant figures.
SECTION 3 — Electricity: circuits & resistance
Q 3.1[A 4]
The circuit shown in Fig. 1 includes three ammeters labelled A₁, A₂ and A₃, and one voltmeter connected across the parallel branch. The supply is 40 V d.c.; R₂ = 30 Ω and R₃ = 10 Ω are connected in parallel, and the voltmeter reads 24 V.
Fig. 1 — circuit diagram (see original exam; optionally paste it here)
For the parallel branch, determine the current shown on each ammeter A₁, A₂ and A₃, and hence the resistance R₁. Show your working.🔬
PhET Simulation — Resistance in a Wire
Run this simulation from the original exam page (or at
phet.colorado.edu → Resistance in a Wire), then answer questions 3.2 – 3.4.Instructions to run simulation: Mute the audio (bottom right corner). Set the values: resistivity ρ = 0.50 Ω·cm, length L = 10.00 cm, area A = 7.50 cm², with R = ρL / A.
Q 3.2[A 2]
An MYP student is investigating the relationship between the resistance of a wire and its resistivity, length and area using the simulation.
State the value of the resistance R shown in the simulation with the settings above, and show that it agrees with R = ρL / A.
State the value of the resistance R shown in the simulation with the settings above, and show that it agrees with R = ρL / A.
Q 3.3[B 3]
Using the simulation, describe how the resistance changes when (i) the length L is doubled and (ii) the area A is doubled. Justify your observations using R = ρL / A.
Q 3.4[C 2]
Evaluate one limitation of using this simulation to model the resistance of a real wire.
SECTION 4 — Ball on a circular track & graphs
🎞
Animation — ball rolling inside a circular track
Observe the motion of the ball in the animation in the original exam, then answer questions 4.1 – 4.3.Consider a metal ball rolling down inside a circular track. It is observed that the ball takes 10.0 s to complete 4 full circles. The time is measured using a stopwatch, with an uncertainty of ± 0.5 s.
Q 4.1[A 1]
Calculate the period of the ball's motion.
Q 4.2[A 1]
Calculate the frequency of the ball's motion.
Q 4.3[B 3]
Determine the percentage uncertainty in the time measurement, and hence in the period. Show your working.
Q 4.4[B 4]
The graph below shows the highest position reached by the ball at the end of each half-oscillation, plotted against time.
Plug in a screenshot of the graph here (from the original exam), then answer on the same axes:
Plug in a screenshot of the graph here (from the original exam), then answer on the same axes:
📈 Graph — highest position vs time
Sketch, on the same axes, the line that shows how the highest position reached changes if the track is made smoother (less friction), assuming the same initial height. Describe your sketch below or attach a photo/screenshot of your drawn line.Take a screenshot of the graph in the original exam and attach it above — it will be included in your PDF.
Your sketch (optional) — paste a screenshot/photo of your drawn line here
Q 4.5[B 3]
Determine the time taken for the ball to reach the maximum height for the first time, using the graph. Show your working. Give your answer to 2 significant figures.
— END OF EXAMINATION —